Accelerator pedal sensor

Gaspedalsensor

10037926a_AM0_white_inclined

The accelerator pedal sensor transmits the position of the accelerator pedal to the engine control unit. Based on this information, the load requested by the driver can be implemented immediately. On this page we will explain the principle according to which modern pedal travel transmitters operate, and which symptoms indicate a fault in this sensor. You will also find out how accelerator pedal sensors are checked in the workshop.

The following technical information and practical tips have been compiled by HELLA in order to provide professional support to vehicle workshops in their day-to-day work. The information provided on this website is intended for suitably qualified personnel only.

How the accelerator pedal sensor works

Accelerator pedal sensor (pedal value transmitter)

Design of accelerator pedal sensor (pedal value transmitter)

Modern vehicles are being equipped with an ever-increasing number of electronic components. Among other things, this is due to legal regulations, e.g. those governing a reduction in emissions and fuel consumption. Electronic components are also increasingly being used to increase active and passive safety as well as driving comfort. One of the most important components is the accelerator pedal sensor.

When it comes to automotive applications, a non-contact sensor based on an inductive principle is increasingly being used. This sensor comprises a stator (which includes an excitation coil, receiver coils, and an electronic evaluation unit) and a rotor (formed of one or more closed conductive loops with a certain geometry).

The application of alternating voltage to the transmission coil produces a magnetic field which induces voltages in the receiver coils. A current is also induced in the rotor conductive loops which, in turn, influences the magnetic field of the receiver coils. Voltage amplitudes are produced depending on the position of the rotor relative to the receiver coils in the stator. These are processed in an electronic evaluation unit and then transmitted to the control unit in the form of direct-current voltage. This evaluates the signal and forwards on the relevant pulse, e.g. to the throttle valve actuator. The characteristics of the voltage signal depend on how the accelerator pedal has been pressed.

Checking the accelerator pedal sensor

The following test steps should be considered during troubleshooting:

Read out fault code
Visual inspection of the accelerator pedal sensor to check for mechanical damage
Visual inspection of the relevant electrical connections and cables to ensure they are properly fitted and for any damage
Check of the sensor using an oscilloscope and multimeter

Using the example of a MB A-Class (150) 1.7, the following test steps, technical data, and figures are listed to explain the troubleshooting work.

Control unit pin	Signal	Test conditions	Reference value
C5 blue-yellow	→	Acceleration off	0 V
C5	→	Acceleration off	4,5 – 5,5 V
C8 violet-yellow	⊥	Acceleration on	0 V
C blue-grey	←	Acceleration on, accelerator pedal released	0,15 V
C9	←	Acceleration on, accelerator pedal pressed	2,3 V
C10 violet-green	←	Acceleration on, accelerator pedal released	0,23 V
C10	←	Acceleration on, accelerator pedal pressed	4,66 V
C23 brown-white	⊥	Acceleration on	0 V

→ output signal ← input signal ⊥ control unit ground

Checking the accelerator pedal sensor: Signal recording from pin C5 — Signal recording from pin C5

SIGNAL RECORDING FROM PIN C5

This measurement checks the voltage supply to the sensor. Ignition on/off.

Checking the accelerator pedal sensor: Signal recording from pin C9 — Signal recording from pin C9

SIGNAL RECORDING FROM PIN C9

Ignition on, press pedal, then release pedal. The signal rises and falls depending on the speed at which the pedal is pressed and released

Checking the accelerator pedal sensor: Signal recording from pin C10 — Signal recording from pin C10

SIGNAL RECORDING FROM PIN C10

Ignition on, press pedal, then release pedal. The signal rises and falls depending on the speed at which the pedal is pressed and released.

The measurements should be performed by two people. The work involved in capturing the signals on the sensor, carrying out various test cycles, and performing diagnostics work on the oscilloscope is difficult for a single person to handle, and it will take them much longer to complete this work.

Accelerator Pedal Training

In this video, we will show you the technologies of the accelerator pedals, how they work and discuss the faults. In addition, we will show the diagnosis of the element? using mega macs and tell you what to look for.

Not helpful at all

5

4

3

2

1

Very helpful

Spare Parts Finder

Manual vehicle identification OE-No.

Spare Parts Finder

Simple vehicle identification with licence plate number Also determine spare parts with OE numbers Detailed product information Find wholesalers near you

You might also be interested in

Basic Knowledge

Tyre pressure monitoring system

Overview of direct and indirect tire pressure monitoring systems (TPMS) - everything you need to know for the vehicle workshop.

Reading time: 15 minutes

Basic Knowledge

NOx-Sensor - Mercedes Benz

If a fault is diagnosed in the NOx sensor when troubleshooting an exhaust gas purification system, this can present a small challenge for a workshop.

Reading time: 6 minutes

Basic Knowledge

Introduction to the Keyless Go system - from function and possible faults to diagnostics, ideal for vehicle workshops.

Reading time: 12 minutes

Basic Knowledge

Adaptive Cruise Control

How to set the ACC radar sensor correctly - with step-by-step instructions and valuable practical tips for the garage.

Reading time: 4 minutes

Basic Knowledge

Checking a high-pressure fuel pump

An overview of the structure and function of the high-pressure fuel pump - with information on fault diagnosis.

Reading time: 8 minutes

Basic Knowledge

Checking the exhaust gas temperature sensor

Step-by-step instructions for testing the exhaust gas temperature sensor - shown on the VW Passat 2.0 TDI.

Reading time: 3 minutes

Basic Knowledge

Injection nozzle/injection valve – Function & checks

Find out how to diagnose a defective fuel injector and replace it in the workshop.

Reading time: 6 minutes

Basic Knowledge

TPS sensor – function & troubleshooting

Learn how to check a throttle potentiometer for defects and recognize the most common symptoms.

Reading time: 2 minutes

Basic Knowledge

Throttle valve switch – function & troubleshooting

Everything you need to know to diagnose and repair the throttle valve switch - helpful workshop tips.

Reading time: 2 minutes

Basic Knowledge

Camshaft position sensor

Learn all about the function and testing of the camshaft sensor and possible symptoms of a defect.

Reading time: 2 minutes